Just how to Replace a Bathtub ( Guide).
Just how to Replace a Bathtub ( Guide).
Blog Article
Hire a Pest Control Company Now
We've uncovered this article pertaining to Installing A Bathtub down the page on the web and reckoned it made sense to discuss it with you here.
Installing a tub isn't specifically rocket science, however it does call for solid plumbing, carpentry, and also sometimes, tiling skills. Changing an old bath tub with a new one is likewise a reasonably difficult job. If the old bathtub is conveniently available, the project can move quickly; if you need to open up a wall to remove the old tub and also place the new bathtub, the job is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly require a helper to move out the old tub as well as embeded in the brand-new one. Make sure you have qualified on your own for the work as well as fit attempting it. Instead of working with a service provider to take over a halfway-completed project, it is far better to think about employing one prior to you begin. Opportunities are you might need a specialist plumber to make tube connections.
This write-up will help you set up a new bath tub in your shower room if you have actually currently gotten a brand-new bathtub and also do not require to alter the arrangement of your previous water supply pipes.
Your tools and material checklist should comprise the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, then the first thing you should do is disconnect the water supply. After doing so, activate the faucets to drain any kind of water continuing to be in the system. The procedure of eliminating the existing faucets can be fairly bothersome as a result of the limited accessibility that is often the case.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the remaining water that will certainly originate from the pipes. Once the supply pipes have been eliminated, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this procedure. When the taps have been removed, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipeline connections on the old taps to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic connector to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin making certain that the washers remain in place in between the tap as well as the sink. Safeguard the tap in position with the manufacturer supplied backnut. As soon as the tap is firmly in place, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical tap ports. The previous type ought to be attached to the faucet ends first, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Using the two wood boards under its feet, position the bathtub in the required placement. The wooden boards are valuable in equally spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little factors.
The following goal is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bath tub until the spirit level checks out degree.
To mount taps, fit the bottom of the furthest versatile faucet port to the appropriate supply pipe by making a compression join; after that do the very same for the various other faucet.
Activate the water supply and inspect all joints as well as brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as additionally examine the overflow electrical outlet and also the typical electrical outlet for leakages.
Lastly, fix the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and securing around the bathtub should wait until the bathtub has been used at least once as this will settle it into its final position.
Preparing for the Installation
Firstly, the supporting structure provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is necessary to make certain that if the faucet includes a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps unit to prevent pressure on the bath tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you use every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to fracture a stiff seal, creating the water to permeate the wall surface between the bathroom and the tiling, causing difficulties with moisture as well as possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly load the bath tub with water before securing, to allow for the motion experienced when the tub remains in use. The sealant can split fairly early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly available on the market. It is suggested to fit the tiles utilizing waterproof or waterproof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very inquisitive about A Step-by-Step Guide to Installing a Bathtub and I really hope you enjoyed the blog posting. So long as you liked our page kindly do not forget to pass it around. We truly appreciate reading our article about How to Install a Bathtub.
Source This Article Report this page